Basket
| Items in cart: Total: |
0 $0.00 |
| View Basket | |
Categories
Mailing List
Subscribe to our mailing list below:Delivery
International Delivery• please ask
Australian Delivery
• $10 flat rate per parcel
up to 15 kilo
• by Australia Post
• from Sydney (Mon - Fri)
Payments
Certified
|
Wahl Clipper Adjustments
Wahl maintenance & warranty information below
This information is provided as a guide only and may not relate to every Wahl product.
Blades should be oiled with a couple of drops before each use for a better cut and reduced wear.
Wahl clipper oil keeps the blades clean and smooth running. Special lubricants assist quiet operation and extend blade life by reducing friction. Coats surfaces of blades with an ultra-thin film of corrosion prevention. A few drops used regularly help ensure longer clipper and blade life together with a better cut.
Wahl clipper adjustments:
|
|
Clipper blades should be oiled before each cut. Place a few drops of oil on the teeth of the blades. For heavy use, oil regularly and ensure you don't overheat the blades. Only use WAHL oil (do not use WD40). Due to the high speed of your Wahl Clipper, the correct type of oil must be used. Do not use hair oil, grease or any oil mixed with kerosene or any solvent as the solvent will evaporate and leave the thick oil, slowing down the blades. WAHL Clipper Oil is a very thin, natural oil which will not evaporate and will not slow down the blades. |
|
|
Power Screw. This is set by Wahl and should not need adjustment. To adjust power, turn the power screw in clockwise direction until you hear a noise. Then slowly turn the power screw out (counter-clockwise) just until the noise stops. This is the maximum power. The clattering when turning the machine on or off is of no consequence; the same for moderate heating and vibration. |
 |
Alignment. The sketch shows how the bottom blade holes are larger than the shanks of the blade screws. When the blade screws are loosened the bottom blade can be aligned with the top blade. Keep the screws tight after the blade is aligned. |
|
1. The end of the top blade teeth should be 1/32", 0.79mm to 1.59mm back from the bottom blade. This is important so that the clipper doesn't cut too close or allow the moving cutter to touch the skin. |
2. Extreme left hand tooth of top blade must be covering or be to the left of the first small tooth of bottom blade. 3. Extreme right hand tooth of top blade must be touching the big tooth on the bottom blade. |
 |
Haircutting at Home. Suggested usage: |
From Wahl's replacement blade guide:
| CLIPPER/TRIMMER | DESCRIPTION | BLADE SET |
|---|---|---|
| WA8358-222 DESIGNER | TAPER BLADE SET | WA1006-400 |
| WA8469 SUPER TAPER | TAPER BLADE SET | WA1006-400 |
| WA9551-512 PRO SERIES RECH | PRO SERIES BLADE SET | WA2094 |
| WA79900-1012 CLIP'N TRIM | PRECISION BLADE SET + OIL | WA2050-500 |
| WA79300-1112 COLOURPRO | PRECISION BLADE SET + OIL | WA2050-500 |
| WA79110-012 BALDFADER | BALDFADER/FINE SURGICAL BLADE SET | WA1026-515 |
| WA9247-612 COMFORT GRIP | PRECISION BLADE SET + OIL | WA2050-500 |
| WA9243-2012 HOMEPRO 22 PCE | PRECISION BLADE SET + OIL | WA2050-500 |
| WA79305-012 VOGUE | PRECISION BLADE SET + OIL | WA2050-500 |
| WA79450-100 COMBO PRO | 100 & 200 BLADE SET (CLIPPER) PERFORMER TRIMMER BLADE SET (TRIMMER) |
WN2108 WA5537-T |
| WA9286-012 SERIES 200 | 100 & 200 BLADE SET | WN2108 |
| WA9155-012 HOMEPRO BASIC | 100 & 200 BLADE SET | WN2108 |
| WA9307-012 MINIPRO | TRIMMER BLADE SET | WN1001-100 |
| WA8964-003 CORDLESS TRIMMER | USA TRIMMER BLADE SET | WA1046-500 |
| WA9879-612 GROOMSMAN XL-2 | XL2 BLADE SET | WA2110 |
| WA9918-1012 GROOMSMAN CORD/CORDLESS | TRIMMER BLADE SET | WN1001-100 |
| WA9910-512 GROOMSMAN USA | USA TRIMMER BLADE SET | WA1046-500 |
| WA9906-708 GROOMSMAN BATTERY | TRIMMER BLADE SET | WN1001-100 |
| WA5537-1201 PERFORMER | PERFORMER BLADE SET | WA5537-BLADE |
| WA9807 LADYGROOM TRIMMER | TRIMMER BLADE SET | WN1001-100 |
| T4205 GROOMSMAN RECH. SHAVER | SHAVER FOIL SHAVER CUTTER |
T42.05F T42.05C |
| T825 LADYGROOM SHAVER | SHAVER FOIL SHAVER CUTTER |
T82.5F T82.5C |
| WA9265 SHOWPRO | PET BLADE SET 30/15/10 STANDARD | WA1037-400 |
| WA9961-801 POCKET PRO | PET TRIMMER BLADE SET | WN1001-100 |
|
Wahl's product Guarantee for many products is now extended to 2 years. |